Case DX35, DX40, DX45 Tractor Service Manual

Table of Contents

SECTION 00 – GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
SECTION 10 – ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
SECTION 18 – CLUTCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
SECTION 21 – TRANSMISSION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
SECTION 23 – DRIVELINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
SECTION 25 – FWD FRONT AXLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
SECTION 27 – DIFFERENTIAL, REAR AXLE . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
SECTION 29 – HYDROSTATIC TRANSMISSION . . . . . . . . . . . . . . . . . . . . . . . . 17
SECTION 31 – POWER TAKE-OFF (PTO) SYSTEMS . . . . . . . . . . . . . . . . . . . . 21
SECTION 33 – BRAKES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
SECTION 35 – HYDRAULIC SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
SECTION 41 – STEERING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
SECTION 44 – 2WD FRONT AXLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
SECTION 50 – CLIMATE CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
SECTION 55 – ELECTRICAL SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
SECTION 90 – PLATFORM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

The following pages are the collation of the contents pages from each section and chapter of the DX35, DX40, DX45 Repair manual. Complete Repair Manual# 87622993.

Manual Extract: CLUTCH Assembly

Assembly
IMPORTANT: When installing a new pressure plate assembly, the pressure plate friction surface must be wiped clean with a suitable solvent to remove the protective film.

1. Lightly lubricate the hub splines of the transmission input shaft with a high temperature lubricant.
2. Use the special tool No. (NH #CNH 299006, CIH #CAS2786) Clutch Alignment Arbor, 1, to position the clutch disc, 2, onto the flywheel, 3.

3. Install the pressure plate, 1, over the clutch alignment arbor, 2, and align the mounting holes.
4. Install the retaining bolts to secure the pressure plate to the flywheel.

IMPORTANT: Tighten the pressure plate retaining bolts evenly and gradually to prevent distorting the pressure plate assembly.
5. Install, tighten, and torque the retaining bolts, 1, to 22 — 28 N⋅m (16 — 21 ft. lbs.).