Case Farmall 65C, 75C, 85C, 95C Tractor Service Manual

Table of Contents

SECTION 00 – GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
SECTION 10 – ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
SECTION 18 – CLUTCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
SECTION 21 – GEAR TRANSMISSION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
SECTION 23 – DRIVE LINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
SECTION 2 5 – FRONT AXLE MECHANICAL TRANSMISSION . . . . . . . . . . . 12
SECTION 27 – REAR AXLE MECHANICAL TRANSMISSION . . . . . . . . . . . . . 14
SECTION 31 – MECHANIAL POWER TAKE-OFF . . . . . . . . . . . . . . . . . . . . . . . 15
SECTION 3 3 – BRAKING SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
SECTION 35 – HYDRAULIC SYSTEMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
SECTION 41 -STEERING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
SECTION 44 – AXLES AND WHEELS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
SECTION 50 – CAB AIR CONDITIONING SYSTEM . . . . . . . . . . . . . . . . . . . . . . 27
SECTION 55 – ELECTRICAL SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
SECTION 90 – PLATFORM, CAB, BODYWORK . . . . . . . . . . . . . . . . . . . . . . . . 50

The following pages are the collation of the contents pages from each section and chapter of the Farmall 65C, Farmall 75C, Farmall 85C, Farmall 95C Repair manual. Complete Repair Manual# 87758598.

Manual Extract: CHECKING THE ALIGNMENT OF THE LEADING WHEELS

Check the alignment of the leading wheels, bearing in mind that for driving in a straight line, the wheels must be at an angle of 2° to the ground, corresponding to a difference of approximately 15 mm (0.5905 in.) for 16” rims, between the top and bottom edges of the rim (fig. a).

When driving in a straight line, the wheels must also be parallel to longitudinal axis of the tractor, or have a maximum of 5 mm toe–in at the front, as measured between the edges of the rims.

To check the toe–in exactly, proceed as follows:

1. Inflate the front tires to a pressure of 2.5 bar (32.26 psi).
2. Place the steering wheel at mid–travel, with one spoke along the tractor center line.
3. Check if wheels are parallel to the tractor center line.
4. On the horizontal plane passing between the centers of the wheels, measure the distance (B) between the front inside edges of the rims (see fig. b).
5. On the horizontal plane passing between the centers of the wheels, measure the distance between the rear inside edges of the rims, checking that the distance is equal to (B) or exceeds it by up to a maximum of 5 mm (0.1968 in.).
6. If necessary, correct the toe–in by adjusting the end of the transverse steering tie–rod.