Case JX55, JX65, JX75, JX85, JX95 Tractor Service Manual

Table of Contents

SECTION 00 – GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
SECTION 10 – ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
SECTION 18 – CLUTCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
SECTION 21 – FRONT TRANSMISSION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
SECTION 23 – MFD TRANSFER BOX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
SECTION 25 – MFD AXLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
SECTION 27 – REAR TRANSMISSION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
SECTION 31 – POWER TAKE-OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
SECTION 33 – BRAKES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
SECTION 35 – HYDRAULIC SYSTEMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
SECTION 41 – STEERING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
SECTION 44 – FRONT AXLE AND WHEELS (2WD) . . . . . . . . . . . . . . . . . . . . . 18
SECTION 55 – ELECTRICAL SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
SECTION 90 – PLATFORM, CAB, BODYWORK AND DECALS . . . . . . . . . . . 27

The following pages are the collation of the contents pages from each section and chapter of the JX Tractor Repair manual. Complete Repair Manual# 87060401.

Manual Extract: WATER PUMP Removal

Proceed as follows:
1. Lower the cylinder head onto the block and screw in the cylinder head bolts (1) fig. 139, finger tight.

Refer to figure 137 for the tightening sequence of the cylinder head bolts on 3-cylinder engines (JX55 and JX65 models).
Refer to figure 138 for the tightening sequence of the cylinder head bolts on 4-cylinder engines (JX75, JX85 and JX95 models).

2. 1st stage — Tighten the bolts (1) to a torque of 70 N⋅m(51 ft-lbs) in the sequence indicated in figure 137 or 138).

3. 2nd stage — Recheck the torque of all the bolts in the sequence indicated in figure 137 or 138.

4. Using the angular tightening tool 380000304 (1), tighten each bolt (2) in sequence through 90o (3rd stage) and then through a further 90o (4th stage) in the sequence indicated in figure 137 or 138.