Fendt 714, 716, 718, 720, 722, 724 Vario S4 Tractors Workshop Repair Manual

Applicable Models:

• Fendt 714, 716, 718, 720, 722, 724 Vario S4 Tractors Workshop Repair Manual – 1885 Pages
• Fendt 700 Vario S4 Wiring Diagram and Schematics – 125 Pages
• Deutz TCD 6.1 L6 4V Diesel Engine Workshop Manual – 577 Pages
• Fendt Tractor Steering Axle ZF-TSA Service Manual – 86 Pages
• Operators Manual – 258 Pages
• Maintenance Manual – 306 Pages

Workshop Manual TABLE OF CONTENTS

• 1 Entire vehicle system
  1.1 Safety instructions
  1.2 General information
  1.3 Vehicle-specific information
  1.4 TechConnect
  1.5 Tightening requirements
  1.6 Fuels and lubricants
  1.7 Technical specification
  1.8 Component position
  1.9 Position of measuring points
  1.10 Calibrations
  1.11 Calibrations fault code
  1.12 Fault code tables
  1.13 Deutz KWP fault code table
• 2 Engine, fuel and exhaust system
  2.1 General
  2.2 Engine
  2.3 Diagnostics
  2.4 Intake system
  2.5 Fuel system
  2.6 Cooling system
  2.7 Lubrication oil system
  2.8 Exhaust gas system
• 3 Front axle
  3.1 Cardan shaft
  3.2 Final drive
  3.3 Front axle suspension
• 4 Steering system
  General
  Steering unit
• 5 Drive train
  5.1 General
  5.2 Rear axle
  5.3 Vario insert
  5.4 Cardan brake
  5.5 Front PTO
  5.6 Rear PTO
  5.7 Front wheel drive
  5.8 Brake system
  5.9 Hydrodamp
• 6 Compressed-air system
  6.1 General
  6.2 Diagram
• 7 Hydraulic system
  7.1 General
  7.2 Hydraulic equipment: Comparison “Variante Power” and “Variante Profi – ProfiPlus”
  7.3 Hydraulic pump
  7.4 Pressure testing
  7.5 Valves
• 8 Electrical system
  8.1 General
  8.2 Electronics concept
  8.3 Fuse assignment
  8.4 Measure and test – CAN bus
  8.5 Measure and test – A components
  
• 9 Cab
  9.1 General
  9.2 Cab
  9.3 Door
  9.4 Washers
  9.5 Windscreen wipers
  9.6 Multi-function armrest
• 10 Air-conditioning system and heating
  10.2 Air-conditioning system
• 11 Rear power lift
  11.1 Power lift
  11.2 Valves
  11.3 Lower link stabilizer
  11.4 Emergency operation
• 12 Service
  12.1 Special tools

Manual Extract

This workshop manual provides notes for trained technicians to maintain our tractors. Read and observe the information in this documentation. This will help you prevent accidents.

Intended use includes maintaining operating the service and maintenance conditions as specified by the manufacturer. Operation, maintenance and repair of the tractor may only be carried out by people who are familiar with this equipment and aware of the associated dangers. Ensure that this documentation is available to and understood by everyone involved in operation, maintenance and repair. Not observing this documentation
can lead to faults, damage and personal injury.

The prerequisite for the Fendt 714, 716, 718, 720, 722, 724 Vario S4 tractor being correctly serviced and maintained is the perfect condition and availability of all necessary equipment, standard tools and general workshop equipment as well as special tools. Special tools must only be used where absolutely necessary. The tools are displayed where they need to be used in each case.

The machine must be maintained according to its proper use. Always replace parts with genuine FENDT spare parts! When ordering parts, please provide the chassis number as per the most up-to-date spare parts documentation.

Workshops should also refer to documentation on maintenance work and technical data. Once maintenance is complete, take a test drive to ensure the vehicle’s correct operation and road safety.