John Deere 1032, 1042, 1052, 1055 Combines Service Repair Manual (TM4413)

Table of Content (Technical Manual – TM4413)

SECTION 10 – GENERAL
Group 05 – Specifications
Group 10 – Testing and adjustments
SECTION 20 – ENGINE REPAIR
Group 05 – Removal and installation, 4-cyl. engine
Group 10 – Removal and installation, 6-cyl. engine
SECTION 30 – FUEL AND AIR SYSTEM REPAIR
Group 05 – Fuel filter with water trap and electrical fuel transfer pump
SECTION 40 – ELECTRICAL SYSTEM REPAIR
Group 05 – Wiring harnesses and connectors
Group 10 – Starting motor (to Serial No. 049283)
Group 11 – Starting motor (from Serial No. 049284)
Group 15 – Alternator (65 A)
Group 16 – Alternator (95 A)
Group 20 – System components
Group 25 – Low shaft speed monitor system
Group 30 – Electromagnetic transmission brake
SECTION 50 – POWER TRAIN
Group 05 – Variable ground speed drive
Group 10 – Engine clutch and mechanical clutch operation (3-speed transmission)
Group 11 – Engine clutch and hydraulic clutch operation (3-speed transmission)
Group 15 – Engine clutch operation (4-speed transmission)
Group 16 – Clutch operating system (4-speed transmission, from Serial No. 049593)
SECTION 50 – POWER TRAIN (Contd.)
Group 20 – Engine clutch (4-speed transmission)
Group 21 – Engine clutch (4-speed transmission, from Serial No. 044137)
Group 25 – Three-speed transmission
Group 30 – Four-speed transmission
Group 35 – Final drives, differential (3-speed transmission)
Group 40 – Final drives, differential (4-speed transmission)
Group 45 – Final drive on rice combine (4-speed transmission)
Group 50 – Track system
SECTION 60 – BRAKES, REAR AXLE AND STEERING
Group 05 – Parking brake (3-speed transmission)
Group 10 – Parking brake (4-speed transmission)
Group 15 – Brake operation
Group 20 – Foot brakes (3-speed transmission)
Group 25 – Foot brakes (4-speed transmission)
Group 26 – Foot brakes with integrated slave cylinder (rice combine)
Group 30 – Rear axle
Group 35 – V-support for wide rear axle
Group 40 – Hydrostatic steering unit
Group 45 – Steering cylinder
SECTION 70 – HYDRAULIC SYSTEM REPAIR
Group 05 – Hydraulic oil reservoir and lines
Group 10 – Hydraulic pump
Group 15 – 3- and 4-spool control valves with flow divider
Group 20 – Hydraulic cylinders
Group 25 – Nitrogen accumulators
SECTION 80 – MISCELLANEOUS
Group 05 – Bearings and shafts
Group 10 – Drive belts
Group 15 – Drive chains
SECTION 90 – OPERATOR’S PLATFORM WITH CAB
Group 05 – Cab ventilation system
Group 10 – Safe handling of refrigerants
Group 15 – Air conditioning compressor
Group 20 – Air conditioning system service and tests
Group 25 – Air conditioning system components
Group 30 – Cab heating system
Group 35 – Operator’s seat
Group 40 – Operator’s cab
Group 45 – Platform control levers
SECTION 100 – CUTTING PLATFORM AND CORN HEAD
Group 05 – Cutting platform and knife drive
Group 10 – Cutting platform auger
Group 15 – Variable reel speed drive
Group 20 – Corn head
Group 25 – Corn head gear case
SECTION 110 – FEEDER HOUSE
Group 05 – Feeder drive
Group 10 – Feeder with integrated platform
Group 15 – Feeder with quick-tach platform
SECTION 120 – SEPARATOR AND CLEANING UNIT
Group 04 – Stone trap
Group 05 – Separator drive
Group 10 – Variable cylinder drive
Group 15 – Threshing cylinder
Group 20 – Concave
Group 25 – Beater variable drive
Group 30 – Beater
Group 35 – Cross shaker
Group 40 – Straw walkers
Group 45 – Cleaning shoe and sieves
Group 50 – Fan and variable fan drive
SECTION 130 – GRAIN PROCESSING
Group 05 – Clean grain and tailings augers
Group 10 – Clean grain elevator
Group 15 – Tailings elevator
Group 20 – Upper tailings auger
Group 25 – Grain tank leveling auger
Group 30 – Grain tank center fill auger
Group 35 – Inner grain tank unloading auger
Group 40 – Riser tube
Group 45 – Discharge tube
SECTION 140 – SPECIAL EQUIPMENT
Group 05 – Straw chopper drive
Group 06 – Straw chopper direct drive
Group 10 – Straw chopper rotor bearings
SECTION 230 – FUEL SYSTEM OPERATION AND TESTS
Group 05 – Fuel filter with water trap and electrical fuel transfer pump
SECTION 240 – ELECTRICAL SYSTEM OPERATION AND TESTS
Group 05 – Electrical circuit and wiring diagrams
Group 06 – Circuit testing
Group 10 – Starting motor
Group 15 – Alternator
SECTION 250 – POWER TRAIN OPERATION AND TESTS
Group 05 – Clutch and mechanical clutch operation (3-speed transmission)
Group 06 – Clutch and hydraulic clutch operation (3-speed transmission)
Group 10 – Clutch operation (4-speed transmission)
Group 15 – Clutch (4-speed transmission)
Group 20 – Three-speed transmission
Group 25 – Four-speed transmission
SECTION 260 – BRAKES, REAR AXLE AND STEERING – OPERATION AND TESTS
Group 05 – Brake operation
Group 06 – Foot brakes and brake operation (rice combine)
Group 10 – Primary (steering) circuit General information and circuit diagram
Group 15 – Primary (steering) circuit Diagnosing malfunctions
Group 20 – Primary (steering) system – Testing
SECTION 270 – HYDRAULIC SYSTEM OPERATION AND TESTS
Group 05 – Hydraulic circuit symbols
Group 10 – Secondary (lift) circuit General information and circuit diagram
Group 15 – Secondary (lift) circuit Diagnosing malfunctions
Group 20 – Secondary (lift) circuit – Testing
SECTION 290 – OPERATOR’S PLATFORM WITH CAB – OPERATION AND TESTS
Group 05 – Cab ventilation system
Group 10 – Air conditioning system
Group 15 – Safe handling of refrigerants
Group 20 – Air conditioning system service and tests
Group 25 – Cab heating system