Toro Sand Pro, Infield Pro 3040, 5040 (Models 8703, 8705) Service Repair Manual

Table of Content – Sand Pro, Infield Pro 3040, 5040 (Models 8703, 8705)

• Title Page
• Revision History
• Reader Comments
• Preface
• Table Of Contents
• 1 – Safety
• Safety Instructions
• Before Operating
• While Operating
• Maintenance and Service
• Jacking Instructions
• Safety and Instruction Decals
• 2 – Product Records and Maintenance
• Product Records
• Maintenance
• Equivalents and Conversions
• Decimal and Millimeter Equivalents
• U.S. to Metric Conversions
• Torque Specifications
• Fastener Identification
• Standard Torque for Dry, Zinc Plated and Steel Fasteners (Inch Series)
• Standard Torque for Dry, Zinc Plated and Steel Fasteners (Metric Fasteners)
• Other Torque Specifications
• Conversion Factors
• 3 – Engine
• Introduction
• Specifications
• General Information
• Fuel Shut Off Valve
• Service and Repairs
• Cooling System
• Air Cleaner Assembly
• Fuel Tank
• Engine
• Briggs & Stratton V-Twin Engine Service Repair Manual
• 4 – Hydraulic System
• Specifications
• General Information
• Hydraulic Hoses
• Hydraulic Fitting Installation
• Towing
• Relieving Hydraulic System Pressure
• Traction Circuit Component Failure
• Optional Hydraulic Accessories
• Hydraulic Schematics
• Hydraulic Flow Diagrams
• Special Tools
• Hydraulic Pressure Test Kit
• Hydraulic Tester (Pressure and Flow)
• Hydraulic Test Fitting Kit
• Measuring Container
• O–Ring Kit
• Wheel Hub Puller
• High Pressure Hydraulic Oil Filter
• Troubleshooting
• Testing
• Before Performing Hydraulic Tests
• Precautions for Hydraulic Testing
• Charge Pressure and Implement Relief Valve (R1) Pressure Tests
• Traction Relief Valve (R3) Pressure Test
• Traction Pump (P1) Flow Test
• Wheel Motor Efficiency Test
• Charge Pump (P2) Flow Test
• Steering Cylinder Internal Leakage Test (Sand Pro 5040 and Infield Pro 5040)
• Service and Repairs
• General Precautions for Removing and Installing Hydraulic System Components
• Check Hydraulic Lines and Hoses
• Flush Hydraulic System
• Charge Hydraulic System
• Hydraulic Tank
• Oil Cooler
• Front Wheel Motor
• Rear Wheel Motor
• Wheel Motor Service
• Lift Control Valve
• Lift Control Valve Service
• Pump Control Assembly
• Hydrostat
• Hydrostat Service
• Lift Cylinder
• Lift Cylinder Service
• Steering Control Valve (Sand Pro 5040 and Infield Pro 5040)
• Steering Control Valve Service (Sand Pro 5040 and Infield Pro 5040)
• Steering Cylinder (Sand Pro 5040 and Infield Pro 5040)
• Steering Cylinder Service (Sand Pro 5040 and Infield Pro 5040)
• Parker Torqmotor Service Procedure
• Danfoss Series 15 Transmission Repair Manual
• Danfoss Series 15 Transmission Service Repair Manual
• Danfoss Steering Unit Service Repair Manual
• 5 – Electrical System
• Electrical Schematic and Drawings
• Special Tools
• Multimeter
• Skin–Over Grease
• Battery Terminal Protector
• Battery Hydrometer
• Spark Tester
• Troubleshooting
• Electrical System Quick Checks
• Component Testing
• Ignition Switch
• Starter Solenoid
• Hour Meter
• Diode Assemblies
• Charge, Start and Interlock Relays
• Seat Switch
• Traction Neutral Switch
• Battery Test (Open Circuit Test)
• Charging System Test
• Service and Repairs
• Battery Storage
• Battery Care
• Battery Service
• 6 – Chassis
• Specifications
• Special Tools
• Wheel Hub Puller
• Service and Repairs
• Front Wheel
• Rear Wheel
• Console
• Parking Brake
• Parking Brake Cable
• Hitch Assembly
• Steering Box (Sand Pro 3040 and Infield Pro 3040)
• Steering Box Service (Sand Pro 3040 and Infield Pro 3040)
• Front Castor Fork (Sand Pro 3040 and Infield Pro 3040)
• Front Castor Fork (Sand Pro 5040 and Infield Pro 5040)
• Operator Seat
• 7 – Electrical Diagrams
• Circuit Diagram – Crank Circuits
• Circuit Diagram – Run Circuits
• Electrical Schematic (machine serial numbers below 400000000)
• Electrical Schematic (machine serial numbers 400000000 to 4034050000)
• Electrical Schematic (machine serial numbers above 4034050000)
• Machine Wire Harness Drawing (machine serial numbers below 400000000)
• Machine Wire Harness Diagram (machine serial numbers below 400000000)
• Machine Wire Harness Drawing (machine serial numbers 400000000 to 403405000)
• Machine Wire Harness Diagram (machine serial numbers 400000000 to 403405000)
• Machine Wire Harness Drawing (machine serial numbers above 403405000)
• Machine Wire Harness Diagram (machine serial numbers above 403405000)
• Optional Light Kit Wire Harness
• Optional Rear Remote Hydraulic Kit Wire Harness (machine serial numbers below 403350000)
• Optional Rear Remote Hydraulic Kit Wire Harness (machine serial numbers above 403350001)
• Optional Hydraulic Switch Kit Wire Harness (machine serial numbers 400000000 to 403000000)
• Optional Hydraulic Switch Kit Wire Harness (machine serial numbers above 403000001)